Carlin EZ PRO GAS BURNER (OIL to GAS conversion burner) WITH COMPLETE ASSEMBLY

Description

CARLIN EZ PRO
OIL to GAS conversion burner
model # 9859210FRU
COMPLETELY ASSEMBLED!
*custom
ized &
assembled for YOUR application*
***this burner will be shipped to you all set up & ready to install***
[complete with gas valve, gasket, nipple, wire nuts, & all hardware]
**the photos show a standard unit.  yours may have a different band installed, a different plate installed, a different size orifice installed, may have the gas inlet on the opposite side, may have a different gas manifold valve, as required for YOUR appliance!
***EACH UNIT IS CUSTOMIZED FOR YOUR SPECIFIC APPLIANCE
AND BTU INPUT RATING!***
This burner requires much set-up work which we do for you!
BEWARE OF OTHER
'PATRIOTIC'
SELLERS!
***SOME SELLERS WILL SELL YOU THIS EXACT BURNER FOR LESS AND LEAVE YOU HOLDING THE BAG!
WE ARE THERE FOR YOU FROM START TO FINISH.
ABOUT OTHER SELLERS SELLING THIS UNIT:
THEY DO NOT PREPARE IT OR ASSEMBLE IT FOR YOU.
NORMALLY--THERE IS ALOT TO DO ON THIS UNIT BEFORE YOU ARE READY TO INSTALL IT.
PLEASE DO NOT THINK THAT YOU JUST BUY IT AND INSTALL IT AND YOU ARE DONE
(as
other
sellers tell
you
---NO--NO---NO!
THERE IS DRILLING,
DE-BURRING
, ASSEMBLY PREPARATION, PIPE JOINT COMPOUND, BAND CHOICE & ADJUSTMENT, BAFFLE SELECTION!
THEY
DON'T DO ANYTHING FOR YOU EXCEPT SELL YOU THIS UNIT.
WE ON THE OTHER HAND COMPLETELY PREPARE AND ASSEMBLE THIS UNIT FOR
YOU
!
***IF YOU JUST WANT IT AS IT IS WITH NO TECHNICAL SUPPORT AND NO ASSEMBLY AND ADJUSTMENTS MADE PLEASE
PURCHASE ITEM  #
231532447800.
THEN YOU WILL NEED TO DO YOUR OWN SET-UP, DRILLING, DE-BURRING, ASSEMBLY, BAND SELECTION, DIFFUSER PLA
TE SELECTION,
AND ADJUSTMENTS INSTEAD OF OUR TRAINED TECHNICIANS!***
This is the burner that should be used in almost every gas conversion job around.  It is virtually maintenance free, SUPER RELIABLE,  and it is a NAME BRAND item!
This burner requires much set-up work which we do for you!
BEWARE OF OTHER
'PATRIOTIC'
SELLERS ON EBAY WHO ATTRACT YOU WITH FANCY BANNERS, FLAGS, CLOWNS, OR DANCING BEARS!
THEY WANT YOU TO BE
'
P
ATRIOTIC'
TO THEM BUT IN FACT THEY ARE NOT EXPERIENCED CONTRACTORS AND WILL FORGET YOU RIGHT AFTER THEY MAKE THE SALE.
THEY ONLY SELL THE UNIT AND LEAVE YOU HIGH AND DRY AFTER THE SALE!
THEY HAVE NO ASSOCIATION OR EXPERIENCE WITH THE ACTUAL INSTALLATION AND MAINTENANCE OF THESE UNITS AND CANNOT AND WILL NOT EVEN ADVISE YOU ON ANY ISSUES YOU MAY HAVE!
THEY CLAIM IT IS A LIABILITY ISSUE---BUT---
THEY JUST DON'T KNOW!
--THAT IS THE TRUTH!
WE WILL BE STANDING BY YOUR SIDE FROM BEGINNING TO FINISH.
BASED ON THE INFORMATION YOU PROVIDE TO US WE WILL DO ALL THE SETTING UP OF YOUR NEWLY PURCHASED UNIT.
WE WILL CUSTOM DRILL & DE-BURR THE ORIFICE, ADJUST THE AIR BAND, INSTALL THE GAS VALVE, INSTALL THE PROPER BAFFLE, INSTALL ALL THE PARTS NECESSARY TO MAKE THIS AN EASY AND SIMPLE INSTALLATION FOR YOU.
ALL YOU WILL NEED TO DO IS TO FOLLOW THE SAMPLE PICTURES AND MAKE YOUR PLUMBING LOOK JUST LIKE THE PICTURES IN THE INSTRUCTIONS AND PRESSURE TEST THE PIPES WHEN DONE.
WE WILL GUIDE YOU THROUGH ALL OF THIS AS NEEDED.
WHEN FINISHED YOU WILL NEED TO HAVE AN EXPERIENCED TECHNICIAN DO A COMBUSTION ANALYSIS TO OPTIMIZE EFFICIENCY AND TO MINIMIZE ANY NOXIOUS EXHAUST GASES.
WE WARRANTY WHAT WE SELL USUALLY LONGER THAN THE MANUFACTURER DOES.
BUY FROM US WITH CONFIDENCE!
WE ARE EXPERIENCED CONTRACTORS
AND KNOW HOW TO DO IT RIGHT!
(We are not like the OTHER GUYS!  We will be with you for technical support post-sale as needed to complete your installation!  You will be issued a cell phone number to our technical support te
am
upon receipt of your unit)
This unit requires precision drilling and reaming of the orifice for the proper BTUs desired.
This service is
INCLUDED
with the purchase of this unit (if desired).
You must give us the equipment information and BTU information from YOUR current unit.
***TECHNICAL INSTALLATION SUPPORT IS ALSO
INCLUDED
BUT IS LIMITED TO THE IMMEDIATE AREA NEAR THE BURNER UNIT ITSELF---NOT THE PLUMBING FROM THE SUPPLY TO THE UNIT.
***ELECTRICAL TECHNICAL SUPPORT IS ALSO
INCLUDED
WITH THE PURCHASE OF THIS UNIT BUT IS LIMITED TO WIRING TO THE BURNER ONLY AND DOES NOT COVER ANY WIRING PREVIOUSLY NOT INSTALLED TO CODE OR INSTALLED IN AN IMPROPER MANNER.
This burner also requires
COMBUSTION TEST EQUIPMENT
when INSTALLATION IS COMPLETE  to be able to measure the exhaust gases and determine if the combustion is safe & correct.
Adjustments can be made depending on the Test Equipment readings and should be done by a licensed GAS technician.
NOTE:
This unit should be installed by an experienced gas installer/service technician BUT if you are mechanically inclined and know gas plumbing and some electrical, you can do most of the installation yourself and save big $$$$.
You WILL however need a technician when done to check your work for possible gas leaks with a pressure tester.
You will also need him to possibly fine-tune your combustion adjustments for proper burn and to adjust it for minimum noxious fumes and pollutants.
DISCLAIMER----PLEASE NOTE:
*Some localities may require a chimney liner be installed when using gas fired equipment.  Please check your local codes.
*Most localities also require a pressure test (by a licensed gas plumber) of the gas plumbing whenever a change/addition is made to the new or existing gas plumbing.
*Also some localities may not allow a homeowner to perform his own gas plumbing or electrical work at all.  Some do and require a pressure test as stated above.  Check your local codes.
*We attempt to assist with technical guidance as best as possible with phone conversations and email/texts, Facetime™, and other media, however BUYER assumes all responsibility when purchasing this product as we cannot guarantee the quality of work by anyone who is not licensed and/or experienced in the installation and use of this product.
*Incorrect or faulty installation of this product can cause serious injury or even death!
*Please check with your local gas plumber BEFORE putting any self-installed appliance into service.
*This unit is offered for sale to knowledgeable handymen and professionals who will also secure the assistance of a licensed gas plumber/electrician or technician to oversee the job.  Buyer assumes any and all risks associated with the purchase, installation, and any related consequences in the installation and or use of this item.
*******ONCE ORIFICE IS DRILLED THIS UNIT IS NON-RETURNABLE!********
SPECIFICATIONS:
BTU
50,000 to 275,000
BTU
(precision drilling or orifice required--we do it for you!)
[GREATER BTU AVAILABLE IF NEEDED--different models available at a higher price--upto 990,000 BTU]
Electrical
Power:
120 vac, 60Hz, 1-Phase
Fuels
Natural Gas
or
Propane Gas (LP)
Technical support may be reached at 'Boilers R Us' ----
Ask for Charlie   9AM - 9PM EST.
Please call our
'Boilers R Us'
center in Lindenhurst, NY
***we are no longer permitted to post our phone number as per eBay***
and ask for Charlie   9AM-9PM - 7 days per week
ALL STOCK ORDERS SHIP WITHIN
6
HOURS OF
PAYMENT!
CUSTOM ORDERS
(like this one)
usually ship within 72-96 HOURS.
FAST SHIPPING!
NEED HELP?
Call our technical support team ----
Ask for Charlie 9AM-9PM only.
HAVE NO FEAR-BoilerGeek IS HERE!
We accept PAY-PAL only.
ALL SALES MUST GO THROUGH E-BAY!
***FAST SHIPPING! ***
**installation available in NY, NJ, C
T
, DE, MD, PA, VA, MA,
RI,
VT, MA,
for an additional fee (0-50)***
ref: 27---16/16/24
This item ships out of our LINDENHURST, NY 11757 shipping facility.
We are no longer permitted to display our telephone number as per eBay policy.
You may contact us by looking up our telephone number yourself on the web (Google) .
Sorry for the inconvenience.
‘BOILERS
R US’ will ship this item to you directly.